Colored filaments project

I am going to have a series of posts about a project I am currently working on. The point of the project is to allow someone to change the color of their 3d printer filament on the fly. So far I have done some tests with different colors of sharpies. This isn’t a new idea in the 3d printing world. Filament Colorizer for example dates back to september of 2011. I plan on taking this idea one step further. The first part involves testing, testing, and more testing. Early last year I began testing the idea by applying a mixture of Rit Dye with acetone to apply to abs filament. The idea was that the acetone would slightly melt the outer layer of the filament and fuse the dye with the abs filament. It did work, but because it would enter the extruder right after this, I decided to abandon this idea for now. Lately I have been doing more testing by coloring the filament with different color sharpies, and also testing how the colors mix within the hotend of the extruder. Here are some pictures of some of my tests. I will continue to post updates on a fairly regular basis as this project grows.

test3

test1

test

Advertisements

My 3d Printer “Haqbot” : Part 2

Now that I have my printer working well, I have started to print it some upgrades to finalize the design to make it more rugged and reliable.  I decided to name my printer “Haqbot” (HackBot) , since my alias is “Haqnmaq” (Hack and Make). I am also now at the stage where I am making the printer look nice. I have added plexiglass sides to the printer, and I am getting the front plate laser cut. I painted a black border around the plexiglass to give it a nice look, instead of just looking at the wiring and extruded aluminum. I also made a plate on the z axis that has the name “HAQBOT’, and it is lit from behind with some RGB leds. I am also doing the same thing on the front panel.

20140417_151020

Here I tried spray painting the acrylic pieces, but the solvents in the paint melted the acrylic panels. I eventually got new plexiglass, and painted it with latex paint instead.

20140420_192106

Here it is with the sides on. It turned out very nice!

20140410_153117

Here is an upgrade to the z-axis that I printed off, because my old one flexed quite easily. BTW This print took 8 hours!!!

20140413_092352

Here is the front plate with “HAQBOT” backlit by some RGB leds. I have 3 switches to control the colors underneath the heated bed, so i’m not just limited to green.

20140424_092708

20140424_092846

Here is an upgrade to the y axis that I just printed off. It has spread apart the X-axis rails to help with the mounting of the extruder.

20140422_114243

This is just a photo of it printing off a scan of my head. I am still using the old X and Y axis here.

My 3d Printer: Part 1

I am currently building a 3D Printer that I have designed from scratch. Except for the circuit boards and firmware, everything else has been designed by me. This is where I will post my progress as I continue to work on it.

 

A little background first. I got my first 3D printer in 2010. I bought a Makerbot Cupcake cnc, which is pretty much the first consumer 3D printer, and it was an amazing thing. Before this you had to either buy a commercial 3d printer which cost $10,000 and up, or you had to build a Reprap, which at that time was still very experimental. The Cupcake cnc was a kit that included everything that you needed to build the printer and even included some of the tools to build it as well. One of the most important aspects of the Cupcake cnc was that you had to build it yourself, which means that you learned what each part on the printer did, and how to fix it if it broke. This knowledge was very helpful in shaping the 3D printers to come. After the Cupcake cnc, many other 3d printer companies popped up and started selling similar types of 3D printers based on the lasercut wood and t-slot connection assembly method. If you were to ask some of these companies what their first 3D printer was, they would likely say that it was the Cupcake cnc.

 

In May of 2013 I decided I wanted to get an updated 3D printer, as the technology had advanced alot since the Cupcake cnc. I considered buying a fully assembled printer, but I didn’t have all the money up front, and I kinda wanted to get my hands dirty. I decided to design and build my own 3D printer. Everything would be designed by me except the electronics and the misc hardware. I also wanted to create a different type of 3D printer than the ones currently available, and different from what other people were building. I decided to build an H-Bot 3d printer, as only a handful of people had built one at the time I started to design mine. An H-bot has a few advantages over other xy-carriage setups, one thing is that both the motors for the x and y axis are mounted directly to the frame so that there isn’t alot of weight on the xy carriage. This is good if you want run the printer at high speeds, but it can be problematic when dealing with the “racking” forces that the xy carriage endures.

To begin, I started designing the printer in Sketchup, and then later I would print the parts off on my Cupcake cnc. I decided to build the frame out of T-slot aluminum, as I can reconfigure and modify the setup easier than I could with a square tube frame. T-slot can get costly, but it is much easier to work with if you don’t want to keep cutting into the frame. I had the basic outline of the printer done when I started to cut the aluminum, so I new what the dimensions needed to be.

20130705_203457

Next I started to build the x and y axis. I also attached the motor mounts.

 

20130726_133644

The x and y axis slides on 8mm linear rod, and 8 linear bearings.

20130726_133741

20130816_225037

20130816_225736

You can see in this photo sort of how the timing belt runs through the x and y axis.

20130816_230646

Here I attached some feet and t-slot ends to the top and bottom.

20130820_182620

 

  Here is the Z axis. It uses an acme threaded rod in the center, and 2 x 12 mm linear guide rods.

20130907_153619

20130904_142551

The platform is mounted to some 20 x 20 mm t-slot aluminum that is attached to the z  axis.

20130912_154217

20130912_154236

I have designed this to be almost fully enclosed, so I attached some cool white led lighting on the inside.

20130917_181340

20130920_154733

Here I test fit the belt, to make sure that it isn’t snagging on anything.

20130927_143023

20130927_143040

This is a new Y end that I printed off. I have changed almost every part on this printer at least once!

20131010_160419

 

 

Here is the main board which will run the printer. It’s the RUMBA from reprap discount.

20131025_093744

Here is a little more progress, including a fan on the x axis (has since been replaced) and the addition of a bowden extruder (which has also been replaced).

 

20131102_185641

20131109_195441

 

 

 Here I am dealing with the mounting of the lcd.

20131110_175410

20131110_184351

Here I am mounting all the electronics to a 1/4″ piece of Acrylic to the underside of the printer.

20131111_180355

I wanted the sd card slot to be flush with the front of the printer, so I created a simple adapter with flex cable that can be mounted to the front.

20131205_194645

I had the RUMBA for probably 4 months until the MOSFET for the heated bed released it’s “blue smoke”. Luckily I was bale to find the part number in the schematics, and ordered a new one. I desoldered the old one, and accidently pulled up a trace, but I was still able to solder on a new one. I took this picture, because I really cant believe that this solder job worked….I honestly thought I had to get a new board. One thing of note is that the MOSFET that was originally used, did not match the part number in the schematic. I wonder if this was to save a few cent’s, or they were just spares from another project, or just an error in manufacturing. Whatever the case, they did not meet the same quality as the original part that was listed, because other people have had a similar problem.

20140211_184220

 

Not all of these photos are up to date. I have gone through a few different extruders, and I have printed out a few other printed parts, but here are a couple videos of it printing.

 

About this blog…

I started this blog to post my ideas and projects that I am working on. I constantly have something I am working on, and I don’t always get a chance to post my progress. I am going to try to post at least something of what I am working on at the time, and maybe some past projects of mine. The posts will be very infrequent, but this is in a way more of an archive than a blog.